• GB/T3037-94 Marine Double-Offset Butterfly Valve — Pneumatic Actuated,TAILCN Marine Valves,GB/T3037-94 Double-Offset Butterfly Valve — Pneumatic Actuated

GB/T3037-94 Marine Double-Offset Butterfly Valve — Pneumatic Actuated

No.GB/T3037-94
Double offset, pneumatic to GB/T3037-94, HT200 / ZG230-450 body, stainless disc, DN80-DN800, 1.0 / 1.6 MPa, Made in Wenzhou, China.
  • GB/T3037-94 Marine Double-Offset Butterfly Valve — Pneumatic Actuated,TAILCN Marine Valves,GB/T3037-94 Double-Offset Butterfly Valve — Pneumatic Actuated

Description

GB/T3037-94 · Marine butterfly valve

GB/T3037-94 is the double-offset (high-performance) butterfly valve: the stem is offset from both the disc plane and the seat centre, so the disc lifts clear before it turns. Metal seat, good to 200 °C and above, with a pneumatic actuator here.

01 · Product details

Product details

Key information for selection. Send your drawing or nameplate photo for an exact match.

ItemValue
StandardGB/T3037-94
TypeDouble offset, pneumatic
Nominal sizeDN80–DN800
Pressure1.0 / 1.6 MPa
Body materialHT200 / ZG230-450 body, stainless disc
ConnectionFlanged, both ends
MediaSea water · cargo oil · steam · hot water
Inspection & certificatesCCS · LR · BV · ABS · DNV · ZC

Materials of main parts

PartMaterialTrademark
BodyCast iron / cast steelHT200 / ZG230-450
DiscStainless steel1Cr18Ni9Ti / 2Cr13
SeatMetal seat with flexible graphiteStellite faced on request
Stem, packingStainless steel / PTFE2Cr13
02 · Overview

Product overview

The double offset removes the rubbing that wears out a concentric seat. The disc swings out of contact in the first few degrees and then rotates free, so the seat sees no sliding load — that is why this pattern is used on hot and abrasive service where a rubber-lined valve fails.

The metal seat is lapped to the disc and gives a tight shut-off over a much wider temperature band than an elastomer. Torque is higher than a concentric valve, so the actuator is sized from the valve torque curve rather than from the DN.

CARGO SHIPTANKERTUGFISHING VESSELNAVAL AUXILIARYOFFSHORE SUPPLY
03 · Buyer information

Frequently asked questions

Concentric or double offset — how do I choose?

Temperature and duty. Below about 80 °C and clean fluid, concentric is cheaper and lighter. Hot, abrasive or frequently cycled service pays for the double offset.

Does the metal seat leak?

It meets the standard's allowable leakage for a metal-seated valve, which is not bubble-tight like a rubber seat. If you need zero leakage at temperature, specify the soft-seat cartridge variant.

Can it be supplied with a classification society certificate?

Yes. CCS, LR, BV, ABS, DNV and ZC inspection can be arranged before dispatch, and the certificate is issued against the actual heat number of the casting. State the society and the surveyor's requirements on the enquiry so it is included in the quotation rather than added later.

Can it replace a part built to another standard?

Our production follows the Chinese national (GB/CB) standards and customer drawings. If the part you are replacing follows JIS, DIN, EN or an IMPA-coded pattern, send the drawing or the flange dimensions: where the bolt circle, bolt count and face-to-face match a GB/CB type, we supply that type. Where they do not, we say so before quoting rather than after.

What do you need from me to quote?

Five things decide the price: the standard number or the drawing, the DN size, the body material, the quantity, and whether a classification society certificate is required. A photo of the nameplate or the old valve is usually enough for us to identify the rest. Delivery port and required date help, but they are not needed for the first reply.