Quality & Certification

What “quality” actually means on a marine valve order

Not a claim on a home page. A set of test records, a heat number that matches the casting, and a certificate a surveyor will accept without asking you to re-test the valve.

Shell test

1.5 × design pressure

Seat test

1.1 × design pressure

Traceability

Heat number on the body

Short answer: every valve is pressure-tested before dispatch, body and seat separately, and is released with a material test report traceable to the casting heat number. Society inspection — CCS, LR, BV, ABS, DNV, ZC — is arranged per order, before dispatch, and the certificate is issued against that same heat number.

01 · The test house

Nine checks a body can be put through before it is released

Mechanical, chemical, dimensional, non-destructive and functional. Not every valve sees every test — the order and the class requirement decide the scope — but the equipment is in-house, so an extra check is a scheduling question rather than a subcontract.

Universal tensile testing machine
Tensile testYield and ultimate strength of the body material, per heat
Charpy impact testing machine
Impact testCharpy notch toughness where the grade specifies it
Dimensional inspection of a valve body
Dimensional checkFace-to-face, flange OD, bolt circle, hole count
Hydrostatic shell pressure test of a marine valve
Shell test1.5 × nominal pressure — body and bonnet joint
Dye penetrant examination of valve bodies
Penetrant inspectionSurface defects at seat and body welds
Valve cycle and function test bench
Cycle and function testFull stroke, stem travel, handwheel torque
Actuator electrical test bay
Actuator testElectrical and control checks on actuated valves
Thermal cycling test chamber
Thermal cyclingSeat and packing behaviour across the service range
High pressure gas test rig
High pressure gas testWhere the standard calls for gas rather than water

Test pressures follow the design standard. For JIS F valves this means JIS F7400; for GB valves, the test clauses of the corresponding GB/T or CB/T standard.

02 · Standards

Which standard your valve is actually built to

A valve quoted as “JIS” without a number is not a specification. The number fixes the face-to-face length, the flange drilling and the test pressure — and those three decide whether it fits the pipe already welded into your hull.

Standard familyCoversTypical pressureFlange standard
GB/T (Chinese national)Flanged and threaded marine valves in cast iron, cast steel, bronze and stainlessPN6 – PN40GB/T 569, GB/T 2501
CB / CB/T (Chinese shipbuilding)Ship-specific valves: storm, sea suction, air pipe head, quick-closing, tank valves0.1 – 1.6 MPaCB series drilling
JIS F (Japanese marine)Full marine valve range by number — F7301 to F7480, each a fixed pattern5K / 10K / 16K / 20KJIS B2220 / B2210
DIN / ENFlanged valves to European face-to-face dimensionsPN6 – PN40EN 1092-1
ANSI / API125 / 150 / 300 LB flanged valves for export and offshore packagesClass 125 – 300ASME B16.5

Mixed-standard enquiries are normal and we quote them as such. A JIS F7351 body on a CB flange pattern is a real question; a valve with no stated standard is not.

03 · Release tests

The tests that decide whether a valve leaves the building

TestWhat it provesPressureRecord
Shell (body) testThe body casting and the bonnet joint hold without leaking or distorting1.5 × nominal pressurePer valve, recorded
Seat tightness testThe disc closes against the seat with no visible leakage at rated pressure1.1 × nominal pressurePer valve, recorded
Material verificationThe casting matches the grade specified — chemistry and, where required, mechanical properties—MTR per heat
Dimensional checkFace-to-face, flange OD, bolt circle and hole count match the standard—Sampling + critical dims 100%
Operation testStem travel, handwheel torque, disc alignment through full stroke—Per valve
Marking checkStandard number, size, pressure class and heat number are cast or stamped and legible—Per valve
Shell mould preparation before pouring
Body poured to the grade on the drawing
Boring the seat pocket of a valve body
Bore, seat face and flange face
Machined bronze valve bodies ready for assembly
Machined bodies, ready for assembly and test

04 · Traceability

The heat number is the whole argument

A material test report that cannot be tied to a specific casting is a piece of paper about a different valve. Every body carries its heat number, cast in or stamped, and the certificate is written against that number. A surveyor can pick a valve off your rack, read the body, and find the same number on the paperwork.

This is also what makes a replacement possible years later. Send the heat number or the nameplate photo and we can usually identify the pattern, the material and the production batch — even for a valve supplied before your current purchasing system existed.

Large marine valve body with worm gear operator
Large bore body — heat number cast into the body, not on a tag
Weld overlay on a valve seat face
Seat overlay recorded against the heat
Heavy section valve body casting
Heavy section body before machining

05 · Society inspection

Class certificates, ordered the right way round

Inspection is booked before casting, not after machining. A certificate requested after the body is finished usually means the casting is re-identified, or the order is re-made.

The surveyor’s witness points are agreed when the order is placed: material identification, pressure test and marking. Some societies witness all three; some only the test.

CNC machining cells at the Yueqing works

Machining cells — parts are held until the witness schedule is complete

State the society on the enquiry

CCS, LR, BV, ABS, DNV or ZC — and the grade of certificate your buyer or yard requires. “Class certificate” alone is ambiguous.

We book the surveyor against the casting date

Witness points are agreed up front: material identification, pressure test, marking. Some societies witness all three, some only the test.

Test in the presence of the surveyor

Shell and seat tests are witnessed and signed. Non-witnessed tests are still performed and recorded for every valve.

Certificate issued against the heat number

It arrives with the goods, not after them. If a certificate is missing on arrival, the shipment is incomplete — treat it that way.

06 · Documentation

What ships with the valve

Standard pack — every order

Certificate of conformity · dimensional drawing · pressure test report · packing list · installation and operating instruction.

On request

Material test report per heat · classification society certificate · welding procedure specification · third-party inspection report · non-destructive examination record.

ISO 9001 quality management system certificate
Quality systemGB/T 19001-2016 / ISO 9001:2015, certified by CCSQA
China Classification Society type approval certificate
CCS type approvalMarine valve product type approval
Welding procedure specification for valve bodies
Welding procedureWPS and qualification record for body repair
CSSC associated enterprise certificate
CSSC membershipAssociated enterprise programme
Marine machinery standards committee certificate
Standards committeePiping accessories sub-committee member
Business licence of Wenzhou Taler Valve
Business licenceWenzhou Taler Valve Co., Ltd.

Documents are issued in English as standard. Other languages can be arranged for the installation instruction on volume orders. Society certificates and the material test report are sent per order, not as a generic sample pack.

07 · Design against failure

Four failure modes we build around

Sea water corrosion at the seat

Bronze bodies with a matching bronze disc where the medium is raw sea water; cast steel is used where strength governs, not where corrosion does. Mixing the two by price is how a valve fails in year three.

Packing gland leakage

Gland depth and packing grade are set for the medium and temperature, not for the cheapest packing available. On steam lines this is the difference between a dry engine room and a daily complaint.

Disc chatter on non-return duty

Swing and lift check patterns are selected against flow direction and pulsation, not against size alone. A check valve one size too large will hammer itself apart.

Flange mismatch on replacement

Face-to-face length and bolt circle are confirmed against the drawing before production. This is the single most common cause of a replacement valve being returned.

Large bore valves on a pump discharge line
Large bore, handwheel operated
Pressure gauges and relief valve on a pipe run
Gauge and relief set on a discharge line
Gate valve installed on a large pipe
Isolation valve on a main

08 · Questions

Quality questions buyers ask

Can I get a certificate for a valve I bought two years ago?

Usually yes, if you can give us the heat number from the body or a clear photograph of the nameplate and marking. Records are kept per production batch. If the heat number is not legible, we can still identify the pattern from the dimensions.

Is the certificate issued to us or to the yard?

To whichever entity is named on the order. Tell us at the enquiry stage; changing the certificate holder after the surveyor has witnessed the test means a new inspection.

Do you accept third-party inspection?

Yes. SGS, TUV, BV and Intertek inspections are all workable, as are buyer-appointed surveyors. Send the inspection scope with the order so the witness points are built into the production schedule rather than added at the end.

What happens if a valve fails the pressure test?

It is not released. The body is re-machined or scrapped depending on where the failure is, and the replacement is tested and recorded the same way. A failed valve never ships with a note.

Need the test standard for a specific valve?

Tell us the standard number and we will send the applicable test pressures, flange standard and documentation list before you order.

Ask a question